Design and simulation analysis of mechanical system of reference network for alignment based on Hefei Advanced Lightsource Facility

Zhang Haiting; He Xiaoye; Wang Wei; Wang Zhaoyi; Li Xiao

doi:10.11884/HPLPB202032.200003

Volume 32 Issue 8

Aug. 2020

Turn off MathJax

Article Contents

Article Navigation > High Power Laser and Particle Beams > 2020 > 32(8): 084003

Zhang Haiting, He Xiaoye, Wang Wei, et al. Design and simulation analysis of mechanical system of reference network for alignment based on Hefei Advanced Lightsource Facility[J]. High Power Laser and Particle Beams, 2020, 32: 084003. doi: 10.11884/HPLPB202032.200003

Citation:

Zhang Haiting, He Xiaoye, Wang Wei, et al. Design and simulation analysis of mechanical system of reference network for alignment based on Hefei Advanced Lightsource Facility[J]. High Power Laser and Particle Beams, 2020, 32: 084003. doi: 10.11884/HPLPB202032.200003

Citation:

Zhang Haiting, He Xiaoye, Wang Wei, et al. Design and simulation analysis of mechanical system of reference network for alignment based on Hefei Advanced Lightsource Facility[J]. High Power Laser and Particle Beams, 2020, 32: 084003. doi: 10.11884/HPLPB202032.200003

PDF( 1405 KB)

Design and simulation analysis of mechanical system of reference network for alignment based on Hefei Advanced Lightsource Facility

doi: 10.11884/HPLPB202032.200003

National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei 230029, China

Received Date: 2020-01-06
Rev Recd Date: 2020-06-05
Publish Date: 2020-08-13

Abstract

Abstract

The accurate measurement and installation of magnet position and attitude in the new generation particle accelerator depends on the comprehensive use of various technologies. To achieve accurate positioning of magnets in the global coordinate system, and fast and precise installation and measurement, thus to build a fourth-generation synchrotron radiation source with high brightness and low emissivity, the National Synchrotron Radiation Laboratory researchers conducted a pre-research on the Hefei Advanced Lightsource Facility (HALF). As an important research content of alignment measurement system, a reference network for alignment (RNA) is proposed. To ensure the accuracy of the alignment measurement, the deformation requirements of the mechanical system of the RNA are very high. Therefore, we performed a static simulation of the entire mechanical system with ANSYS software, and optimized the alignment reference plate based on the analysis results to meet the requirements of working conditions, and laid a solid foundation for subsequent pre-research.
- Hefei Advanced Lightsource Facility,
- magnet alignment,
- reference network for alignment,
- statics,
- optimized design

FullText(HTML)

References(10)

References

[1]	王巍, 何晓业, 姚秋洋, 等. 磁铁快速安装准直方法在HLSⅡ升级改造中的应用[J]. 强激光与粒子束, 2015, 27:045104. (Wang Wei, He Xiaoye, Yao Qiuyang, et al. Application and research of magnets rapid installation and alignment method in HLSⅡ upgrade project[J]. High Power Laser and Particle Beams, 2015, 27: 045104 doi: 10.3788/HPLPB20152704.45104
[2]	Wang W, He X Y, Wang P, et al. The surveying data processing of control network based on HLS upgrade[C]//Proc of IPAC. 2013: 2986-2988.
[3]	孔祥元, 郭际元, 刘宗泉. 大地测量学基础[M]. 武汉: 武汉大学出版社, 2010: 44-49. Kong Xiangyuan, Guo Jiyuan, Liu Zongquan. Foundation of geodesy[M]. Wuhan: Wuhan University Press, 2010: 44-49
[4]	张正禄, 李广云, 潘国荣, 等. 工程测量学[M]. 武汉: 武汉大学出版社, 2005: 227-230. Zhang Zhenglu, Li Guangyun, Pan Guorong, et al. Engineer geodesy[M]. Wuhan: Wuhan University Press, 2005: 227-230
[5]	王小龙, 董岚, 李波, 等. BEPCⅡ储存环的预准直[J]. 核技术, 2010, 33(8):566-570. (Wang Xiaolong, Dong Lan, Li Bo, et al. The prealignment of the BEPCⅡ storage rings[J]. Nuclear Technique, 2010, 33(8): 566-570
[6]	刘祖平. 同步辐射光源物理引论[M]. 合肥: 中国科学技术大学出版社, 2009: 161-162. Liu Zuping. Introduction of physics of Synchrotron Radiation Light Source[M]. Heifei: University of Science and Technology of China Press, 2009: 161-162
[7]	张森, 杨玉萍, 季彬彬, 等. 龙门加工中心横梁组件静动态分析及结构改进[J]. 组合机床与自动化加工技术, 2013, 8:56-56. (Zhang Sen, Yang Yuping, Ji Binbin, et al. Finite element analysis and structure improvement of gantry machining center crossbeam component[J]. Modular Machine Tool & Automatic Manufacturing Technique, 2013, 8: 56-56
[8]	陈宇. 泡沫铝夹芯结构油罐车罐体优化设计及其关键性能分析[D]. 葫芦岛: 辽宁工程技术大学, 2017: 32. Chen Yu. Optimization design and key performance analysis of aluminum foam sandwich structure tank[D]. Huludao: Liaoning Technical University, 2017: 32
[9]	张朝晖. ANSYS 12.0热分析工程应用实战手册[M]. 北京: 中国铁道出版社, 2010: 423. Zhang Chaohui. ANSYS 12.0 practical handbook for the engineering thermal analysis[M]. Beijing: China Railway Press, 2010: 423
[10]	聂小军, 刘磊, 康玲, 等. 一种废束站束窗结构设计与优化[J]. 强激光与粒子束, 2018, 30:105105. (Nie Xiaojun, Liu Lei, Kang Ling, et al. Structure design and optimization of a dump beam window[J]. High Power Laser and Particle Beams, 2018, 30: 105105 doi: 10.11884/HPLPB201830.180057